Starlink Gen 2 Single-Port Gigabit Ethernet Adapter — RJ45 LAN Adapter, 1 m Lead

The Starlink Gen 2 router has no wired LAN port. This adapter adds one. Plug the adapter into the Gen 2 router, then plug a standard Ethernet cable into the adapter's RJ45 port and run it to your own router, switch, PC, camera, or any Ethernet device. The lead is about 1 m long, so the adapter sits close to the router.

Category:

Starlink Gen 2 (Standard Actuated / V2) routers ship without an Ethernet port. If you want a wired connection — a third-party router, a mesh node, a switch, a desktop PC, a game console, or a security camera — you need an adapter like this one.

Starlink Gen 2 Ethernet adapter connection — dish, adapter, RJ45 cable to third-party router, 39.37 inch length

One end plugs into the Gen 2 router. The other end is a standard RJ45 Gigabit port. From there it is a normal wired network: any CAT5e/CAT6/CAT6a/CAT7 patch cable connects the adapter to your device. No setup, no software. Plug it in and the wired link is live.

Starlink Gen 2 Ethernet adapter cable cutaway — PVC jacket, foil shielding, 26 AWG, retail box

The lead is about 1 m (see the length note below — two images give different numbers). The cable is shielded CAT5e FTP: 16 cores in total, eight 26 AWG conductors plus eight 30 AWG conductors, with Mylar and aluminium-foil shielding, a ground, and a PVC jacket. The adapter box is a compact grey enclosure with the RJ45 port on one end and a molded Gen 2 plug on the other. It carries a CE mark and “Made in China” on the case.

Use it at home to wire a TV or console, in an office to feed a switch, or in an RV or cabin to connect a third-party router when Wi-Fi alone is not enough. It is a spare-friendly part too — installers keep one in the kit for Gen 2 jobs.

Key facts / specs

  • Fits: Starlink Gen 2 / V2 router systems (Standard Actuated)
  • Output: one RJ45 Gigabit Ethernet port, up to 1 Gbps
  • Lead length: about 1 m (see warning — images disagree: 39.37 in / 1 m vs 35.4 in / 90 cm)
  • Cable: 16-core shielded, CAT5e FTP; eight 26 AWG + eight 30 AWG conductors
  • Shielding: Mylar + aluminium foil, with ground
  • Jacket: PVC
  • Connectors: molded Gen 2 plug one end, RJ45 port on the adapter box
  • Plug-and-play, no configuration

Length note: two images give different numbers — 39.37 in / 1 m and 35.4 in / 90 cm — so the lead is about 1 m.

Compatibility

Fits Starlink Standard Actuated (Gen 2 / V2) only.

Does NOT fit Standard (Gen 1), Standard (Gen 3 / V3), Flat High Performance, or High Performance dishes. The picture in the gallery spells this out: Gen 2 gets the green tick, the other four get a red cross. Not for Starlink Mini.

This is a third-party compatible accessory, not an official SpaceX product. Starlink is a trademark of SpaceX.

Application scenarios

  • Third-party Wi-Fi router, mesh system, switch, or access point behind a Gen 2 router
  • Wired link for a desktop PC, workstation, or NAS
  • Gaming, streaming, cameras, and other latency-sensitive devices
  • Home, RV, cabin, office, and remote-site networks

Starlink Gen 2 Ethernet adapter compatibility — Standard Actuated Gen 2 only, not Gen 1, Gen 3, Flat High Performance or High Performance

Related Products