Detachable LC HDMI Fiber Optic Cable 4K@60Hz

A 4K HDMI cable that comes apart. Two small HDMI modules — one Source, one Display — plug into a thin LC fibre run, so you can pull the bare fibre through a wall or conduit first and clip the modules on afterwards. No fat HDMI plug to force through a hole. The signal rides on LC-LC OM3 multimode fibre, which is why it holds 4K at 60 Hz over distances where a copper HDMI cable gives up, and it picks up no electrical interference on the way.

This is not a fixed cable with moulded HDMI plugs on both ends. It is a two-piece system: a pair of HDMI modules and an LC fibre run between them. The Source module goes on the player, PC or console end, the Display module on the TV or projector end, and the fibre in the middle is a standard LC-LC OM3 patch — the same kind of fibre already sitting in most structured-cabling jobs. If the fibre is already in the wall, the modules just plug into it.

On performance: the spec sheet rates it up to 18 Gbps, 4K at 60 Hz or 1080p at 120 Hz, over HDMI 2.0 with HDCP, EDID and CEC. It is an active optical design — the modules convert the signal to light and back — so there is no copper in the long run and no EMI or RFI to worry about, even next to power cables or in an industrial setting. The jacket is a slim OD2.0mm, in PVC or LSZH, so it bends through tight conduit.

Two things to read carefully before ordering. First, distance: the spec sheet says up to 100 metres, but the supplier’s own connection diagram and the retail box both say 300 metres. Those two numbers do not agree, so this page does not pick one — confirm the run length you need before promising a customer a number. Second, power: the spec sheet says the modules are powered through the HDMI port and need no external power, but the modules have a micro-USB power port on the side, the price list describes them as “with MICRO power port”, and the boxed kit ships with two power adapters and two 1.2 m micro-USB cables. The connection diagram also shows DC 5 V going to both modules. In practice the port is there if the source or display cannot feed the modules enough power on its own — keep the adapters handy on a long or awkward install.

The kit lengths in the supplier’s April 2025 price list are 4 ft (1.22 m), 6 ft (1.83 m), 10 ft (3.05 m) and 15 ft (4.58 m). Those are the lengths the modules are listed with, not the maximum run — the fibre trunk itself can be ordered to the length the job needs.

Good for a conference room where the rack is down the hall, an auditorium or control room, a classroom or church with the projector far from the source, a home theatre with the gear in another room, or any job where the cable has to go through a wall first and the plugs go on last.

Key facts / specs

  • Detachable two-piece system: HDMI Source module + HDMI Display module, joined by LC-LC OM3 multimode fibre (50/125 μm)
  • HDMI male to HDMI male (modules); LC/UPC fibre connectors on the module ends
  • Resolution: 4K@60Hz / 1080p@120Hz (spec sheet notes optional 8K versions — not confirmed for the modules shown)
  • Bandwidth: up to 18 Gbps
  • Signal format: TMDS via active optical engine; HDMI 2.0, HDCP, EDID, CEC
  • Cable diameter: OD2.0mm; jacket PVC or LSZH (optional)
  • Max transmission distance: conflicting sources — spec sheet says up to 100 m; supplier connection diagram and box say 300 m (985 ft). Confirm before promising a distance.
  • Kit lengths listed in the supplier price list (April 2025): 4 ft (1.22 m), 6 ft (1.83 m), 10 ft (3.05 m), 15 ft (4.58 m) — kit lengths, not the maximum run
  • Power: spec sheet says powered via HDMI, no external power required — but modules have a micro-USB power port (visible in the photos), the price list lists them as “with MICRO power port”, and the boxed kit includes 2 power adapters and 2 × 1.2 m micro-USB cables; connection diagram shows DC 5 V to both modules
  • Operating temperature: -20 °C to +70 °C; indoor use (industrial options on request per the spec sheet)
  • Boxed kit contents (as shown in the package photo): box, Receiver × 1, Transmitter × 1, power adapter × 2, micro-USB cable 1.2 m × 2, user manual

Compatibility

Works with HDMI source devices (PCs, media players, consoles, AV receivers) and HDMI displays (TVs, projectors, monitors) that support 4K@60Hz. The fibre run between the modules must be LC-LC OM3 (or a compatible LC patch panel / coupler setup). The modules are directional: the Source end goes to the source device, the Display end to the display.

Application scenarios

  • Long-distance AV in conference rooms, auditoriums and control centres
  • In-wall and conduit installs where the fibre goes in first and the modules follow
  • Home theatre with the equipment rack in another room
  • Broadcast studios and digital signage with strict AV requirements
  • Industrial environments needing noise-free signal transmission
  • HDMI extension over existing LC fibre infrastructure, patch panels or couplers

Links