Blog

November 17, 2026

Starlink in Winter: Snow Melt, the Three Settings, and the Cable Check Before the First Storm

The first snow of the season is the wrong time to find out your dish can’t keep up — or that the cable you buried in October has a nick in it. Starlink dishes are built to melt their own snow, but the feature only works if you set it right and the rest of the install is sound. Here’s the short version, before the weather turns.

There is no separate heater

A Starlink dish doesn’t have a heating element tucked behind the face. It turns its own power up and the antenna’s heat melts the snow. That matters for two reasons: it works only while the dish has power, and it costs watts — something to remember if your dish runs off a battery or a power station at a cabin.

The three settings

In the Starlink app, go to Settings, then Starlink, then Snow Melt. There are three modes:

  • Off. No heating at all. Fine where snow is rare, or when you can brush the dish off by hand.
  • Automatic. Starlink detects snowy conditions and heats only when needed. This is the one Starlink recommends, and it’s the right choice for almost everyone — including anyone running from a power station, since it doesn’t burn power on a clear cold night.
  • Pre-heat. Keeps the dish warm so snow can’t get a grip in the first place. Starlink’s own words: “This option may increase power consumption.” Use it the night before a forecast storm, when the dish is out of reach, or when the snow is wet and heavy — then switch back to Automatic.

If you do nothing, check the setting now. A lot of dishes sit on whatever mode they shipped with, and Off in a snowstorm is a quiet way to lose the connection.

How fast it melts depends on which dish you own

Starlink publishes a snow-melt rating for each dish, in millimetres of snow per hour:

  • Mini: up to 25 mm an hour — about 1 inch.
  • Standard (Gen 3, now sold as Standard 4X): up to 40 mm an hour — about 1.5 inches.
  • V5: also 40 mm an hour, which Starlink rounds to 1.6 inches on that sheet. Same 40 mm, different rounding.
  • Performance (Gen 3): up to 85 mm an hour — about 3.5 inches. Older sheets for this dish said 75 mm, so if you see 3 inches quoted somewhere, that’s the old number.

Those are melting capacities, not promises. Starlink’s own warning is blunt: “Heavy snow completely covering the dish may cause intermittent connectivity or temporary loss of service.” A blizzard dropping two inches an hour will outrun a Mini, and even a Standard will fall behind in the worst of it. When the snowfall rate drops back below the melt rate, the dish catches up and the connection comes back.

All three of the smaller dishes are rated to run from -30 °C to 50 °C (-22 °F to 122 °F). The Performance dish goes further, -40 °C to 60 °C. The router and power supply are a different story — Starlink rates those for indoor use, 0 °C to 30 °C (32 °F to 86 °F). Keep them in the house or a heated shop, not an unheated barn.

What not to do

Don’t cover the dish. A tarp, a bucket or a homemade hood hurts performance and stops the snow melting. Don’t chip at ice with a scraper, a pick or hot water — Starlink says light ice generally doesn’t affect performance, and a soft brush from the ground is the most you should do. Never climb a slick roof to clear it.

The check most people skip: the cable

Snow Melt keeps the face clear, but it can’t fix a damaged cable, and winter is when cable damage shows up — meltwater finding a nick in the jacket, a crushed section under a window frame, a join left out in the rain. Before the first storm, walk the run: look for a chewed or cracked jacket, check the seal where the plug meets the dish, and make sure any outdoor join is actually weatherproofed, not just taped.

Our Gen 3 replacement cable is CAT5e FTP, 24 AWG, rated at 1 Gbps, in 2, 10, 15, 23, 30 and 46 m — long enough to route the cable properly instead of stretching a short one across a roof. If the run has to go through a wall, that’s what the Gen 3 RJ45 adapter pair is for: two short leads with IP68 waterproof couplers that turn the dish plug into a standard socket, so the long middle run can be ordinary shielded Ethernet cut to length and kept dry at both ends.

And if your Mini runs off a battery at a cabin or on the ice, remember the heating draws extra power on top of the Mini’s usual 25 to 40 W. Size the battery for a storm day, not a clear one — our Mini USB-C PD cable (100 W) and Mini DC to DC cable (65 W) are the two ways to feed it straight from a power station or a 12–48 V battery without an inverter in the loop.

Set Snow Melt to Automatic, check the cable, and let the dish do the rest.

Sources: TrendyTechTribe, “Starlink Snow Melt: How It Works, Power Draw & Fixes 2026“, checked against Starlink’s published specification sheets for the Mini, Standard, V5 and Performance dishes (November 2026).

Related: Starlink Mini on the road: power options compared

gerry Uncategorized
User avatar
About gerry
Gerry is with JINSHANG electronic tech(FEV Electronics), a cable manufacturer in Changzhou, China. The team makes Car amplifier Installation wiring kits(car audio cables), Starlink Gen 3, Gen 2 and Mini replacement cables, adapters, power cables and roof mounts, and customized cable assemblies for medical, industrial, consumer and automotive use. He writes here about picking the right cable for the job — lengths, power, mounts — and what actually works in the field.