On 13 November, a Starship put 26 more V3 satellites into orbit. A day later, the launch tower caught the ship itself — the first time an orbital-class upper stage has ever been caught and brought back. Two things happened on one flight, and only one of them changes your internet.
What Flight 15 actually did
The launch went up from Starbase, Texas, on Friday 13 November, carrying 26 Starlink V3 satellites — the second batch of the new generation, after the first 26 went up on Flight 14 in late September. All 26 made contact within minutes of deployment and are healthy, according to Michael Nicolls, Starlink’s engineering lead, on 14 November. They are raising themselves to their operating orbit now, and SpaceX says they should start serving customers a few weeks after launch.
Then came the part that made the news. Ship 42 flew 14 orbits — about 22.5 hours — and came back to the tower, where the mechanical arms caught it at 21:20 UTC on 14 November. Boosters have been caught three times before, on Flights 5, 7 and 8. An upper stage that has actually been to orbit had never been caught until now. The booster on this flight, B22, didn’t make it back: its guidance system decided its position was wrong and diverted it into the Gulf of Mexico on its own. SpaceX says the cause is under investigation.
What a V3 satellite is
Each V3 is built for about 1 terabit per second of downlink and 160 Gbps of uplink — roughly ten times a V2 satellite’s downlink and about twenty-two times its uplink — with 2,048 beams in each direction, where a V2 had 192. SpaceX reckons one Starship load of V3s is worth about ten Falcon 9 launches of V2 Minis. There are now 52 V3 satellites in orbit.
The factory side matters as much as the rocket. Starbase’s booster production director, Danny Fain, said on 13 November that each booster takes seven to eight months to build, but building several in parallel means one booster every four weeks and one ship every two weeks. Hardware is no longer the bottleneck — launch licences and the number of pads are.
When you actually feel it
Not this month. Fifty-two satellites is a start, not a network. SpaceX president Gwynne Shotwell has said a few hundred V3s need to be up before users really feel faster speeds, possibly by mid-2027; Musk puts the critical mass at about 1,000, around the second quarter of 2027. Most users today see 100–200 Mbps, and the dish itself still tops out around 400 Mbps. The V3s in orbit now are a down payment on gigabit service, and the 36 new ground gateways the FCC cleared last week are the other half of the same build-out — the satellites are only as fast as the ground stations behind them.
So if your speeds look the same next week, nothing is wrong. The change lands gradually, a few dozen satellites at a time, and it lands first in congested areas where the network is thinnest — the same places where dynamic pricing already kicked in this month.
What doesn’t change
Your dish and your cable don’t change. No new dish is needed for V3 service, and the cable between the dish and the router is the same one it has always been. If anything, the ground side of your setup matters more now, not less: as the space side gets faster, the weak link moves closer to home — the gateway, the router, and the run of cable from the dish to where the router actually sits. If you’re putting the router in the middle of the house instead of on the wall where the cable comes in, measure the route first — dish to eaves, down the wall, through to the middle of the house, with slack for a drip loop — and buy the length that fits the route. Our Gen 3 replacement cable comes in 2, 10, 15, 23, 30 and 46 m, shielded (CAT5e FTP, 24 AWG, 1 Gbps), so the run can go the proper way round the house instead of the shortest way across a roof.
Sources: Stray Dog, “SpaceX catches a Starship upper stage for the first time” (15 Nov 2026); editusa, “Starship deploys 26 Starlink satellites after booster diverts offshore” (13 Nov 2026); WorldIncredible, “Starlink Satellite Capacity: Musk’s 1 Tbps V3 & 100,000 V4 Plan” (Nov 2026).

